Rivet Shelving (Boltless Shelving)
Rivet shelving assembles in minutes with a rubber mallet — no nuts, bolts or clips. Beams slot into keyhole uprights and lock under load, so the shelf gets more rigid as you fill it. The most popular choice for archive rooms, workshops and e-commerce fulfilment.
Key Features
- Tool-free boltless assembly — rubber mallet only
- Single-rivet and double-rivet beams for light or heavy duty
- Particle board, MDF or steel panel decks
- Shelf height adjustable in 25–50 mm (1–2 in) increments
- Add-on bays share uprights to cut cost per metre
- Ships flat-packed for low freight cost
Specifications
- Material: Q235 steel frame, powder coated
- Load per shelf: 300–800 kg (660–1,760 lb)
- Shelf width: 900–2,000 mm (35–79 in)
- Shelf depth: 300–900 mm (12–35 in)
- Frame height: 1,500–2,500 mm (59–98 in)
- Levels: 3–6
- Deck options: particle board / MDF / steel panel / wire mesh
- MOQ: 1,000 sets, trial orders from 500 sets (one set = one complete bay)
Available Models
| Model | Size (H x W x D) | Load per Level (kg) |
|---|---|---|
| RV183-1 | 183 x 90 x 40 cm | 150 kg |
| RV201-1 | 201 x 90 x 40 cm | 150 kg |
| RV220-1 | 220 x 90 x 45 cm | — |
| RV183-2 | 183 x 90 x 45 cm | — |
| RV183-5 | 183 x 90 x 60 cm | — |
| RV183-7 | 183 x 75 x 30 cm | — |
All load ratings shown are per shelf level. Multiply by the number of shelves to get the total bay capacity. Bays are tested with uniformly distributed loads on flat, properly anchored shelves.
Product Gallery
Built for workshops, archives and fulfilment
Rivet shelving is the workhorse of the range. Beams slot into keyhole uprights and lock tighter as the load comes on, so a bay that goes together in minutes with a rubber mallet ends up stiffer than bolted shelving of the same gauge. Single-rivet beams suit light archive loads; double-rivet beams take the 800 kg end of the range. Uprights are roll-formed from Q235 steel and powder coated, and add-on bays share uprights to cut the cost per running metre.
Packing and container loading
Units ship knocked down. Uprights, beams and shelf panels are bundled and flat-packed, so a 40 ft container carries far more bays than it would with assembled units — which is where most of the freight saving comes from. Before dispatch we photograph the loaded container and send the loading record, so what leaves our floor is what you can check against your own receiving documents.
- Uprights, beams and panels bundled separately and labelled per bay
- Flat-packed to maximise container fill and cut freight cost per unit
- Container loading photos and inspection record sent before the ship sails
- Mixed sizes consolidated into one shipment against a combined MOQ
Frequently asked questions
What does the 300–800 kg per shelf range depend on?
It depends on the beam profile and the bay width. Single-rivet beams at narrow widths sit at the 300 kg end of the range; double-rivet beams at the widest spans reach 800 kg. Tell us the load and the span and we will size the beam rather than guess. Each level is rated as a uniformly distributed load with the bay level and anchored.
Which sizes can I order?
Shelf widths run 900–2,000 mm (35–79 in), depths 300–900 mm (12–35 in) and frame heights 1,500–2,500 mm (59–98 in), with 3 to 6 levels adjustable in 25–50 mm steps. Non-standard sizes are made to order — send a drawing or the dimensions you need.
Can I add bays to a run later?
Yes. Add-on bays share the uprights of the bay beside them, so extending a run costs less per metre than buying standalone units, and the uprights are already punched to take the extra beams.
What is the minimum order quantity, and can I mix sizes?
1,000 sets per order (one set = one complete bay), trial orders from 500 sets on request, and mixed sizes count towards the same total. That lets you test several configurations in one shipment instead of committing the whole order to a single size.
Can you match our colour?
Blue, orange, black and grey are held in stock. Any RAL colour is available on request, matched either to your own brand or to racking already standing in the building.
Can I get a sample before placing a full order?
Yes. Samples are supplied against a small deposit, and that deposit is refundable against your first production order.
What warranty do you offer?
Warranty runs from the bill of lading date and is tiered at 1, 2 or 3 years depending on the product line. It covers manufacturing defects only; overload, misuse, and damage caused by the site or floor are excluded.
Can I arrange a third-party inspection?
Yes, and we welcome it. Inspection can be arranged at the factory before dispatch or at the port; the inspection fee is payable by the buyer.
What do you send me before the goods ship?
We send the inspection record and container loading photos proactively. Mill certificates, dimensional reports, coating thickness readings and load test reports are available on request.
What happens if the goods arrive damaged?
Send us photos or the inspection report and you will have a written resolution proposal within 48 hours of us receiving them.
Get a Quote
Tell us the size, the load per shelf, your target quantity and where the goods are going. You’ll get pricing, lead time and one or two questions worth settling before you commit — usually within 24 hours. Mixed sizes, trial orders and OEM/ODM are all welcome.
Related guides
- How to Choose Warehouse Shelving — load per shelf, bay sizing, decking and container planning.
- Boltless vs Bolt-Together Shelving — assembly time, stiffness and when each system wins.
- Shelf Load Ratings Explained — UDL versus point load, and the eight numbers to ask for.
- Importing Steel Shelving from China — an eleven-point buyer’s checklist.
Other products: Heavy Duty Shelving · Tire Rack · T Hole Shelving · Grooved Shelving · Full Steel Shelving · Slotted Angle Shelving